Saturday, February 19, 2011

How to Make a Dollhouse Miniature "Marble" Topped Wine Rack from Card Stock, Part 2

During the time you are laminating the parts for your table you can be sealing the top for the marble finish.

I attach the top to a toothpick with sticky wax and use an acrylic finish.  I used Delta's PermEnamel Satin Glaze.  This will seal the cut edges and surface of the mat board.  I applied two coats, let these dry thoroughly.  I sanded using 320 grit sand paper and applied one more coat, nice and smooth.  Coat both sides; you can paint around the toothpick.  Let dry.


Another thing you can do is make the wine bins.  I made the bins from Coats & Clark Classic Crochet thread.  I tried other materials but the crochet thread worked best.  


Tape your card stock pattern to your table. 







 Tape a piece of waxed paper over the pattern.














 I found the easiest way to lay the thread on was to affix the tape to one end of the thread first.
















Next, line up the thread and press the taped end down.

Pull the other end and tape it down.







Do one direction first then the other.














Use the yellow wood glue to glue where the thread crosses with itself.  Get between the layers of the thread and be neat.  It will count later.  Let this dry.






Before you take the wine bin off the pattern make marks on the thread where the pattern ends.  This will give us a guide to cut on.


Lift the waxed paper off the table and set it aside. 


Tape another piece of waxed paper over your pattern and make the second wine bin.


Are the 3 coats of satin glaze dry on your top, yet?  If they are you can give the top at least 3 coats of white paint.  I used Delta's Ceramcoat Magnolia White.  Paint 2 coats, both sides (around the toothpick), let dry thoroughly.  After the top is dry sand smooth, use 320 grit sand paper and apply another coat of paint.  If you think you need more coats, apply them. When you are satisfied sand lightly and give a smooth final coat of paint.  We want complete coverage.












You've got a lot of things going on right now, haven't you?  There are parts and pieces everywhere.




If your wine bins are made and the glue is dry carefully cut them away from the waxed paper.  If you have any glue globs at the crosses carefully cut them away.


Are your wine racks dry?  If they are we can assemble the bins into the racks.
You will probably have to trim, if you do, take a little bit off at a time, dry fit again, trim again.  When you get them to fit, glue the bins into the racks.  Glue the bins so that they are even with one side of the rack.  Let these dry.
Get the apron that you set aside earlier.  Cut a piece of mat board that fits in the center, between the long sides, on the underside of the apron.  Cut this piece of mat board 7/8" (23mm) wide.





Glue this piece of mat board to the center of the underside of the apron.














Measure and mark the center of this piece for later.  Set this aside again.


















Glue 4 layers of 1/8" (3mm) card stock together, these strips should be at least 3" (71mm) long.










After the strips are glued together and dry measure and mark 4 pieces at 5/8" (16mm) long.


Cut these pieces and set them with the wine racks.













When the wine bins are dry, good and dry use a brush and black acrylic craft paint and paint the thread.  I spray painted my first table without doing this step and the spray paint made the thread fuzzy.  We are going to spray paint the table, but paint the thread first.  Let this dry.
Dry them on waxed paper with the flat side on the paper.  Don't leave them to dry like I have them here.


                            Are you making legs?





Get the wine racks and the little 5/8" (16mm) long strips together.  These little strips are to be glued; two at the bottom corners of the wine racks; I glued mine to the outside of the racks.  











The other 2 strips are glued a little higher, at the top of the second 1/2 diamond.  Let this dry. 















This assembly needs to be straight and square.














When the first side is done and has dried, glue the other side to it.












Glue the wine rack to the underside of the apron.  Center the rack side to side, front and back.  Set it down and check if the top is level.  Let Dry.






End of Part 2

How To Make a Dollhouse Miniature "Marble" Topped Wine Rack From Card Stock


I saw this table in an old Williams-Sonoma catalog and liked it.  I tear pictures out of catalogs and tape them all over my room, "To Make Some Day".  I have a soft spot for wrought iron.  I don't know why, I don't buy any wrought iron in full size.  We will have more tutorials on card stock wrought iron.
This project will take a couple of days to complete.  It really is in your best interest to let the laminated pieces of card stock dry and cure in the forms for the most consistent results.  Letting the shapes cure in the forms will give you less headaches when the assembly starts.
We are going to use card stock, mat board, crochet thread, flat black spray paint, black acrylic craft paint and Elmer's yellow wood glue or TiteBond yellow wood glue for making the table.
The marbling will require Delta's PermEnamel Satin Glaze, Delta's Ceramcoat Magnolia White, Americana's Glazing Medium, a charcoal pencil (extra soft), 320 grit sand paper and a small sponge.
 Cut 2 pieces of mat board 2 3/4" (7cm) x 1 1/4" (32mm).  Use a new blade in your craft knife and try to keep the blade perpendicular to your table.  We don't want beveled edges; the edges need to be straight up and down.  If you have access to a scroll saw, use it.
Cut one of these pieces a little smaller; take off about 3/32" (2mm) on one short end and one long side.
 
I have used 320 grit paper to round off the top edges on all four sides of both pieces.  Use yellow wood glue to glue these two pieces together.  Center the smaller one on top of the larger one.  This gives your "marble" top a fancy edge.  Weight this down to prevent warping.
The wine rack pattern is on the left and the leg pattern is on the right.
I have drawn a 1 inch square and a 3mm square on the pattern that you are to copy.  Load the pattern into a program that you can adjust sizes with.  When your squares measure 1 inch or 3mm you have the right size.  Print the patterns onto card stock and cut them out.  
Use the wine rack pattern first.  Trace the pattern onto 2 pieces of mat board. Be careful, and cut slowly, making many passes with the craft knife.  You don't have to cut through the first time.
When you have the 2 pieces cut out glue them together with the yellow glue, weight or clamp until dry.
 Use an old candle to wax the edge all around.  The wax will prevent the glue from sticking to this edge.  This is your wine rack form. 
A Note:  You can try using one layer of mat board for your forms, I am sure it will work if care is used.  I have a scroll saw and I cut the mat board after it's been glued together, so I use two layers. 
We are going to use 1/8" (3mm) wide card stock.  Quilling paper comes to mind, I know.  Quilling paper probably would work, but you would have to glue more layers together for the strength we get from fewer layers of card stock.
Mark the card stock at 1/8" (3mm) intervals and cut using a straight edge and craft knife or if you have a paper trimmer use it.  I usually cut a few ahead.
To begin making wine rack hold your strip of card stock on the bottom and pull the card stock around the form to the other side of the bottom, overlap the strip and glue the card stock together.  We will be using yellow wood glue throughout the tutorial. 
I have overlapped the card stock and glued it together. 
When you run out of card stock butt the ends and start another strip.  Keep wrapping the card stock around the form until you have four layers.  I make tick marks on a scrap of paper to help me remember how many layers I have.  
 

Let this dry on the form at least a couple of hours.  After it is dry, make another.
 To make the apron (the support for the "marble" top) cut one piece of mat board 2 7/16" (62mm) x 1 1/16" (27mm).  Use the 1/8" (3mm) wide card stock and wrap this piece of mat board with four layers of card stock, gluing the card stock to the mat board.  Keep one side of the mat board even with one side of the card stock.  One side will be flat while the other will have a lip.  Set this aside for now.
Trace the leg pattern onto 2 pieces of mat board.  You are using the shaded area on the pattern.  Cut out the pattern and glue the 2 pieces of mat board together to make the leg form.  Clamp or weight this down until dry.
Wax only the edge I have marked in the picture.
 To begin to make a leg, glue the end of the 1/8" (3mm) card stock strip over the top corner, just a bit to anchor the first strip.
 Bring the strip down around the curve to the end (foot).  A rubber band helps to hold the first strip in place.
It also helps to push the card stock strip back into the curve when you are making the foot.
I  also use a quarter inch dowel that has been sharpened in a pencil sharpener for a useful tool making this leg.
(I have a couple of layers on here and I am shaping with the dowel.)
 
 For the first layer only cut a bit extra of the card stock and fold to the outside of the tip (foot) and glue this down.
For the second and consecutive layers (make 5 layers) DO NOT FOLD and GLUE the ends.  Begin the second layer by spreading glue onto the card stock at the top, lay the second layer of card stock on and continue spreading glue and pressing the card stock into it.  I use the sharpened dowel to press the card stock together and shape the foot.  Cut the card stock off even with the ending tip.  
After you have 5 layers on the form spread some glue on the outside layer, this is just to help stiffen the leg.
When the table is assembled it is very study.
Set this aside to dry, at least a couple of hours, overnight would be better.  If you work you could make a leg in the morning, take it out when you get home; make another leg to dry overnight and take it out in the morning and so on.
To remove the leg from the form use your craft knife to cut the card stock at the top corner and the tip of the foot.  If the leg is sticking to the form, run your craft knife between the form and the leg.  Make 4 legs.
This is the end of part 1

Sunday, February 6, 2011

Information

Hi Guys,
Checking in on my old favorite rug site, it's changed and they don't have the selection of rugs they used to have, but I did find some useful information.  www.woodworkersauction.com/architecturalstyle.htm  This defines styles in a short, but definitive way, useful I thought.

Are you snowed in?  We received about a half inch of ice and maybe a couple of inches of snow on top.  The weather people were predicting over a foot of snow, a few days later they said a couple of more inches and just to the south of us they received 8 inches.  I had gone grocery shopping on the weekend so we were good for food and we had drawn water into everything that could hold water.  We have a well and electricity pumps the water.  My  husband wanted to be sure we had enough feed for the donkeys so I had to go out to get feed for the donkeys on the day of the ice, I bought some Diet Pepsi and a big bag of Peanut M&M's for me so I could last through the storm.  My son took me out and he drives an old 1990 Ford pickup, that sounds funny saying 1990 is old, he doesn't have heat so the defrost wasn't working and his wiper blades were awful.  We took a little longer than expected and the ice started coming down and freezing to the windows.  We live about 20 miles out of the city.  He stopped along the way to scrape the windshield. We came to the little town 6 miles from where we live and stopped for gas and checked a car repair garage.  They were open and had some wipers, they even put them on for us.  HooRay!!  We got home, that deserves a Pepsi!
I hope you all are safe and warm, I'm stocking the furnace with plenty of locust logs, it burns the hottest.  Thinking of a wine rack with a marble top for this months tutorial.  I saw it in an old Williams-Sonoma catalog.  Figuring out the ways and hows.

Talk to you all later,  Kris

Tuesday, February 1, 2011

How to Make a Miniature Vintage Sink, Centimeters

My little lady is canning beans for the state fair.  She is hoping for a Blue Ribbon this year.  That Gladys McGillicutty always takes the Blue Ribbon!
I have had a request for centimeters for my sink in the vintage kitchen
I am just going to go through it again adding the centimeters to the instructions.  I am going to get as close as I can just by using my ruler to convert.  In miniatures your"eye", what looks "right" to you can go along way.
Here goes . . . . .
This is how I made the kitchen sink for the kitchen room box.  I made the sink from wood, gesso and a jelly container, the small single serve kind from restaurants.  If that's not available I've used any "bubble" packaging that is the size of the sink I want, this one is 39 mm x 45 mm, (1 1/2" x 1 3/4").  I have frustrated many a sales person looking around for the "right size" package, not the a particular product, but what the product is packaged in!
Start out with a piece of 3mm (1/16") thick basswood, 48 mm x 109 mm (1 7/8" x 4 1/2").  Cut a hole in the center for your sink.  I am now going to refer to this piece as the sink top.  The plastic bubble should have a flange that you can use to glue the "sink" onto the basswood.  I glue the "sink" under the top.  Don't glue now, just don't trim this flange off.  Measure the sink and cut the opening, 11 mm (3/8") from the back and 4 mm (1/8").  You can use an exacto knife, cutting a little bit at a time, sand smooth.

We are going to add on to the sink top by gluing more wood to the top of it for a thicker edge, for a back of top and for drain board ridges.

From almost 4 mm (3/32") basswood cut a strip 11 mm (3/8") wide and 109 mm (4 1/2") long.  Soften one edge of this piece with sandpaper, it should not be square, diagram A.

This piece is glued toward the back of the sink top, on top of the of the sink top.  This piece is where the faucet will be glued on.  Glue the strip on using wood glue, that's a yellow color.  If you haven't got that Elmer's white glue will do, it will just take a little longer to set up.  If you can clamp this piece together, do it.  Spring type clothes pins make pretty good clamps.

From almost 4 mm (3 3/32") basswood cut a strip 4 mm (1/8") wide and 109 mm (4 1/2") long, also cut 2 strips 4 mm (1/8") wide and 45 mm ( 1 3/4") long.  Soften the top 2 edges of these 3 pieces, diagram B.

Glue these pieces onto the sink top according to diagram C.  Clamp and let dry.  When dry slightly round off the front 2 corners of the sink top.







Round off the front corners of the sink top after you remove the clamps.  Just take the sharpness off.





When everything is dry I sanded a slight slope to the drain boards going toward the sink opening.

Cut from almost 4mm (3/32") basswood 3 mm (1/16") wide strips.  If you have access to 3 mm (1/16") wide half round use that.  If you don't have access to half round, round off the top 2 edges of the almost 4 mm (3/32") x 3 mm (1/16") strips according to diagram B.  These are the drain board ridges.  I glued 6 of these onto each side of the sink opening.  You'll need to clamp these down if you sanded the slope in the sink top.

Before you glue the sink to the underneath side of the sink top, cut a hole in the center of the plastic container for your drain.  I found a plastic cap about 6 mm (1/4") and stuck a straight pin in the center, painted it silver and dotted it with black on the inside of the cap to simulate the drain holes.  This became my sink strainer/basket.

Another option for the sink drain opening is to use a gripper snap for the rim and leave out the strainer/basket.  Gripper snaps are found in the notions department of a fabric store.  They are the kind that are fastened to the fabric with points that are pushed through the fabric and then the points are bent over.  These are not the sew on kind of snaps.

When you are satisfied with all of your sanding, glue the sink to the underneath of the sink top and set this assembly aside.


Sink Cabinet

Follow the sizes in the diagrams for cutting out the sink sides, back and front.  Round off the top 2 corners of the back.  Glue the sides onto the back, bottoms even, the back will be 11 mm (3/8") taller, that's the back splash.




































Follow this drawing to glue the front and back to the sides.














Cut from 3 mm (1/16") basswood a strip 11 mm x 112 mm (3/8" x 4 3/8"), this is to be painted black and will be glued onto the bottom front of the cabinet, it's the back of the toe kick.

The doors, drawers and center vent are made from 3 mm basswood, (1/16").  Cut 25mm x 45 mm ( 1" x 1 3/4"), cut 4 for doors.

The drawers are 25mm x 12 mm ( 1" x 1/2"), cut 2.

The center vent is 27 mm x 12 mm ( 1 1/16" x 1/2"), cut 1.

With sand paper, soften all four edges of the doors, drawers and vent.

I cut vent slots with an Exacto knife,  I've also seen a shape cut out and filled with decorative screen.  Cross stitcher's perforated paper would work for this.

Glue the sink top onto the cabinet.  The sink top will be longer and wider than the cabinet by just a bit, center the cabinet under the sink top from side to side and it should have all the extra towards the front.

I use gesso to smooth everything in. all the seams need to be filled.  I paint gesso over the whole sink top and let it dry.  The gesso will sink into the seams, so you will have to paint the gesso on a few times.  After you've got everything filled you can sand it all smooth.  Remember, you want this sink to look like a piece of cast iron with the smooth finish of porcelain.

When that's done paint the sink top and cabinet.  Paint the doors, drawers and vent separately.  I used Rustoleum white, it's an oil base enamel and gives a good appliance finish.  Paint and sand between coats with fine sandpaper, I will use up to 400 grit to get a good smooth finish.  When you are satisfied with the surface, do not sand the last coat of paint.  Glue on the doors, drawers and vent.  Paint the toe kick black and glue it to the front bottom of the sink cabinet.

Go to the kitchen roombox stove for a little more explaination of the painting.

I don't make my kitchen cabinets or appliances open.  I am not going to open them and I don't leave them hanging open.  They aren't hanging open in my full size kitchen.  I think leaving them open in a miniature scene emphasizes that it is a miniature.  I am going for as much realism as I can achieve.

For the handles I painted a plastic drinking straw with silver spray paint.  Then I tried to slice off identical widths, then I cut these in half.  I glued the half slices, the handles, to the front of the doors and drawers with super glue.

Glue your strainer/basket in.  I ordered a faucet from Hobby Builders, #938, I believe it's $6.99.

I hope I have the conversions right.  I know we want to try to stay to 1 inch scale as much as possible, but sometimes we just have to go by "eye" and that's just fine, too.

Have fun, expand on it, make it better, just keep making minis!!!!  Oh, and send pictures, too!

Talk to you all later, I have a special order to draft . . . . . . . Kris